When a customer comments on a condition related to tire pressure monitoring, it is very important to distinguish between Check Tire Pressure / Low Tire Pressure conditions and Service Tire Monitor system issues. Understanding the difference between the two distinct conditions will help you distinguish between normal system operation (tire needs air) and a system malfunction.


2007 Buick Lucerne, Rainier

2006-2007 Cadillac DTS, Escalade Models

2007 Cadillac SRX

2006-2007 Chevrolet Avalanche, Impala, Monte Carlo, Suburban, Tahoe

2007 Chevrolet Equinox, Silverado, Trailblazer

2006-2007 GMC Yukon Models

2007 GMC Acadia, Envoy, Sierra

2007 Pontiac Torrent

2007 Saturn AURA, OUTLOOK

2007-2009 Saab 9-7X

2008-2010 GM Passenger Cars and Trucks (including Saturn except ASTRA)

2008-2010 HUMMER H2, H3

There are two important differences between a Check Tire Pressure / Low Tire Pressure message/light and a Service Tire Monitor message light:

Tire Pressure Light Service Tire Monitor System (light blinks, and then stays on)

The Tire Pressure Light will blink for about one minute and a Service Tire Monitor message will be displayed when a system malfunction occurs. For example: If one or more tire pressure sensors does not transmit information for 18 minutes of driving, the TPM system WILL set a code, display a message, and BLINK the light for about a minute, after which the light will stay on solid for the remainder of the ignition cycle. If the system fault is intermittent, the message/light may also be intermittent -- on during some ignition cycles, off during others.

Low Tire Pressure Warning (light stays on solid)

If the TPM system detects a tire pressure below the threshold, the Check Tire Pressure message and the Tire Pressure Light will come on and stay on. The message and light may be intermittent in nature, especially during cold weather.

Conditions that will cause the low tire pressure warning message/light to display:

* Check Tire Pressure / Low Tire Pressure message/light will stay on solid and no system codes are set. The TPM system is operating as designed. Correcting the tire pressure will resolve the issue.

* Service Tire Monitor message/light will blink and system codes WILL set.  There is a condition that should be diagnosed and corrected. The tire may have picked up a road hazard and/or have a slow leak.

The effect of outside temperatures on tire pressures

Important: As a rule of thumb, tire pressure will change about 7 kPa (1 psi) for every 6°Celcius (10°Fahrenheit) decrease in temperature -- dropping when it gets colder outside, rising when it gets warmer.

• The tire pressure may not have been checked in the past six months.

• The air pressure in a cold tire may be at the pressure where the system is required to warn the driver. However, that same tire will rise in temperature and pressure as the customer drives, causing the message and light to go out.

• The tires may have been rotated, pressures adjusted, and the new tire positions were NOT re-learned into the vehicle. This can occur on vehicles that have two different placard pressures for front and rear tires.

• There may be a slow leak in one of the wheel and tire assemblies (valve stem, wheel rim or aluminum wheel porosity leak).

Tire puncture repair procedures for all cars and light duty trucks

Tire pressure should be set to the specified placard pressure at the lowest seasonal temperature the vehicle will encounter during operation.The correct action to avoid a Check Tire Pressure message due to extreme temperature changes is to do the following:

• Use an accurate, high quality tire pressure gauge.

• Re-learn the TPM sensors and adjust the tire pressure to the placard values after every tire rotation.

• Let the vehicle sit and adjust the tire pressure to the specified value when the tire temperature is at the lowest expected temperature.

• Never set the tire pressure below the placard value regardless of tire temperature or ambient temperature.

Important: On extremely cold days, if setting the tire pressure when the vehicle has been indoors,

it may be necessary to compensate for the low outside temperature by adding 21-27 kPa (3-4 psi) more than the placard pressure. At some later time, when convenient and when the tires are cold (outdoors), the pressure should be re-checked and a djusted to the placard pressures if necessary.

Using the TPM tool

TPM Tool J 46079 software updates and hardware update kit

The J 46079 TPM tool is a valuable aid in diagnosing system faults with TPM systems. It is a software-driven tool that REQUIRES periodic updatesin order to work on new model cars and trucks. Failure to update the tool with the latest software version may result in possible misdiagnosis.

TPM Software Version 3.5 has recently been shipped to each GM dealership in the J 46079-30 TPM update kit. All future TPM software updates will be posted in GM DealerWorld (U.S) or the GMinfoNET (Canada) as needed. Under the Support tab , access "TPM Downloads."

This update consists of two parts: Sensor transmission signal strength is displayed in the upper left corner of the main display next to the tool's battery level display. When the tool is used in both activate or scan mode, it will receive the sensor's transmission and indicate its signal strength. It is important to note the sensor's transmission signal strength since it is a good indication of an accurate diagnostic.

TPM Tool J 46079 user tips

The placement of the TPM Tester's antenna when activating a sensor is critical, especially with the latest software update. When activating a sensor, the antenna tip of the TPM Test J 46079 must be placed on the sidewall, perpendicular to the tire, and close to the valve stem. This will assure proper activation of the sensor. If the antenna of the TPM Tester is placed either on the valve stem or on the wheel itself, the tool may not properly activate the sensor, causing improper diagnosis.

Diagnostic tip

If you encounter a sensor that does not respond when activated by the tool, try activating another sensor that responded previously. This will help you determine if the tool is able to activate the sensor or if you have a problem with one particular sensor.

• A hardware update kit that consists of a custom rechargeable battery pack, battery cover with charging terminals, and a charging cradle with a smart charger where the whole tool will fit into the cradle for charging (same concept as a cordless phone). This hardware update substantially increases the life of the batteries and will assure that the TPM Tester always has full battery capacity.

• The software update will add new vehicles and also improve the speed of the tool's read-back ability and accuracy.

Diagnostic tip

When using the tool during a sensor learn procedure, use the "Activate" soft key on the tool. Press the key for one second then release and the tool will perform an LF (low frequency - 125 kHz) activation cycle. You do not have to hold the key until the vehicle acknowledges. Holding the key will just reduce battery life. The LF activation of the sensors wakes them up and forces them to transmit their IDs immediately. This allows a much shorter sensor learn procedure than using the Delta P method.